2003 toyota camry torque specs. Toyota Camry Bolt Torque Specifications 2019-03-05

2003 toyota camry torque specs

2003 Toyota Camry Sedan Specifications, Pictures, Prices

2003 toyota camry torque specs

Step 2: Bolts 1 - 8 to 88 N路m 65 ft. As a general rule, a four-cylinder engine requires more torque than a V-6. The struts have upper mounting nuts tightened to 30 rear struts or 60 front foot-pounds; the bolts connecting it to the steering knuckle are around 155 foot-pounds and the damper shaft nut is around 35 foot-pounds. Install the 90 mm 3. In this position it will be vertically upwards.

Next

Toyota 3.0L

2003 toyota camry torque specs

The crank gear will have a dot also. Do not use rearward-facing child seats in any front passenger seat. It will line up at 90 degrees from the top, towards the front of the car. Do not put objects in front of an airbag or around the seatback. It has 3 white lines on it and and arrow mark. I assume you know this already since you didn't ask. If not, replace the bolt.

Next

2003 Toyota Camry Solara

2003 toyota camry torque specs

The intake manifold typically requires from 130 inch-pounds to 22 foot-pounds, while the exhaust manifold nuts and bolts are from 27 to 36 foot-pounds. Of course you need to remove and compress the tensioner also. Do not use a torque wrench for this step. If it is a 6 cyl then the marks would be- camshafts both with dots up and lined up with indicaters on heads and crank timing mark on 0 with the harmonic balancer installed. In all other accidents, the airbags will not inflate.

Next

2003 toyota camry le camshaft cap torque specs

2003 toyota camry torque specs

To decrease the risk of injury from a deploying airbag, always wear seatbelts, sit upright in the middle of the seat as far back as possible from the airbag modules and do not lean against the door. Put the arrow facing away from the engine. The brake hoses connect to the caliper with a banjo bolt at a torque of about 22 foot-pounds. . In sequence, torque all bolts. The pan that contains the automatic transmission fluid is mounted with its bolts tightened to approximately 69 inch-pounds; the drain plug is tightened to 35 to 36 foot-pounds.

Next

2003 Toyota Camry Sedan Specifications, Pictures, Prices

2003 toyota camry torque specs

Torque: 50 Nm 37 ft-lbs In sequence, turn each bolt an additional 90 degrees. The fuel rail is usually mounted at a torque of 84 to 180 inch-pounds. With the belt installed with all lines on their proper dots and arrow away from the engine, you valve timming is correct. Torque: 30 Nm 22 ft-lbs. The throttle body is mounted to a torque of less than 100 inch-pounds for a V-6 engine or 20 to 22 foot-pounds for a four-cylinder. Torque: 70 N路m {714 kgf路cm, 52ft路lbf} c Mark the front of the cylinder head bolts with paint.

Next

Toyota Camry Bolt Torque Specifications

2003 toyota camry torque specs

Mar 31, 2014 Quote: Originally Posted by norvelplagbao52 1993 saturn sl2 1. The driver and front passenger airbags are designed to deploy in severe usually frontal collisions where the magnitude and duration of the forward deceleration of the vehicle exceeds the design thresholjd level. Step 3: Bolts 1 - 8 again to 88 N路m 65 ft. Originally Posted by norvelplagbao52 1993 saturn sl2 1. The brake calipers are often mounted at a torque of 25 foot-pounds, while the torque plate bolts are about 79 foot-pounds for the front brakes and 34 to 46 foot-pounds for the rear. Please see the Owner聮s Manual for further instructions.

Next

2003 Toyota Camry Sedan Specifications, Pictures, Prices

2003 toyota camry torque specs

Install the 108 mm 4. Tighten head bolt number 9 Cylinder Head Bolts Location and Tightening Sequence to 33 N路m 25 ft. Go on line to toyota camry head bolt torque then find the autozone page and you will find diagrams of how to do it. Torque: 30 Nm 22 ft-lbs. The side-impact airbags are designed to inflate in severe sideimpact collisions. The cam gears have a dot punched into them near a certain tooth. In sequence, torque all bolts.

Next

Toyota torque specifications

2003 toyota camry torque specs

Most bolts fastening the ball joints to the steering knuckles and control arms require a torque of just over 90 foot-pounds. A manual transmission does not have a pan but the drain and fill plugs have the same torque as the drain plug on the automatic. Visit for more information on the Toyota Camry Solara. This is where the solid white lines will line up with. The spark plugs torque from 160 inch-pounds to 20 foot-pounds. This is where the broken line will match up with.

Next

2003 Toyota Camry Sedan Specifications, Pictures, Prices

2003 toyota camry torque specs

At the same time the notch in the crankshaft pulley timing flange should be opposite the 0 degrees mark on the timing marks on the front of the lower belt cover. Engine 4-Cylinder V6 Type 2. The upper camshaft sprocket has a smaller hole in the web. Apr 19, 2010 Tighten the cylinder head bolts 1 - 8 in the sequence shown in Cylinder Head Bolts Location and Tightening Sequence Using the 4 step torque turn method, tighten according to the following values: Step 1: Bolts 1 - 8 to 61 N路m 45 ft. The stabilizer bar connects to the strut with a link whose bolts have a torque of 30 rear to 55 front foot-pounds. The oil pan under the car is mounted with bolts tightened to around 80 inch-pounds.

Next