These maximum payload ratings are intended for comparison purposes only. Children are safer when properly secured in a rear seat in the appropriate child restraint. It was also the 50th year anniversary of truck production by releasing a white and gold special edition truck. The weight of passengers, cargo and options or accessories may reduce the amount you can tow. Your actual range may vary based on several factors including temperature, terrain, and driving technique. Besides acting as a motor mount, the tube adds strength between the front crossmember and the frame rails on both sides. The big steps over the rear suspension will require a newly shaped bed floor that goes over the rails, but it sure gives a killer on-the-ground stance when finished.
Maximum payload ratings are intended for comparison purposes only. Cargo and load capacity limited by weight and distribution. At the front of the chassis, the optional rounded frame horns will accept stock bumper brackets. Oh, and I was just joking about the purists, I have complete respect for the work it takes to restore any vehicle to factory spec. The weight of passengers, cargo and options or accessories may reduce the amount you can tow.
Children are safer when properly secured in a rear seat in the appropriate child restraint. Does anyone have any experience with a 4x4 frame swap on a 2wd 61 Apache 20? These will fit on our standard Chevelle spindle. See for details and limitations. Cargo and load capacity limited by weight and distribution. We also offer 3-styles of Panhard bars: the one shown on top of the housing, our Low Roll-Center Panhard bar that goes behind the housing and is parallel with the housing, and a diagonal link style. The weight of passengers, cargo and options or accessories may reduce the amount you can tow. Cargo and load capacity limited by weight and distribution.
Requires compatible iPhone and data plan rates apply. The three-hole style is our Street Rod Style mount and the multi-hole style is our Drag Racing Style mount. Cargo and load capacity limited by weight and distribution. All of our brackets are laser-cut and tumbled to provide you a clean, good looking bracket and a cleaner weld and consistant fit during production. Click here to see all Chevrolet vehicles'. This car runs, and it runs strong. Awesome Paint and Detail Work! With its available Duramax 2.
Different steps over the rear suspension are available, up to 10-inches and over the front up to 4-inches. The only thing original on this bronco is the tub and frame. I got a 76 4x4 frame and pulled the spring hangers off and put them on my 61 4x4 frame. The weight of passengers, cargo and options or accessories may reduce the amount you can tow. Joek, I'll keep you in mind when I go to sell the frame, and drivetrain. .
The tabs on the edge of the rails are bed mounts. Scooter Trash has uploaded 763 photos to Flickr. Both brackets will offer you an adjustable stance at the rear. Combine these steps over the suspension with ShockWave bags and you're on the ground. Trust Ecklers for all of your restoration and replacement needs for your truck, racer, show car, street rod, or daily driver. In this photo, the brackets are tack-welded to the 3-inch diameter axle-housing tubes. The jig-built mandrel-bent chassis features 2X4X.
This will give a much lower stance. We offer either a 2X4 box tube fabricated step over the rear suspension shown or a 2X4 box tube mandrel-bent step over the rear. It also keeps the antisway bar arms tight against the rails. Your pickup chassis can ordered with up to a 10-inch step over the rear suspension, while the front chassis step is available up to 4-inches more then stock. This direct-replacement chassis will fit the cab and the bed on this chassis, without modifications to the bed floor.
All fees and programming subject to change. We can not drill a 5-on-5 pattern in the 11-inch Chevelle rotor. In the next photo, you can see the four mounting-holes. Click here to see all Chevrolet vehicles' destination freight charges. We are happy to say we do not wire-weld any Jim Meyer components in our shop! The forward crossmember, just in front of the Panhard bar, is a thru-frame tubular crossmember that houses the optional rear antisway bar inside. Side-marker reflectors were added to all fenders this year. Services are subject to user terms and limitations.
Services are subject to user terms and limitations. Just in seafoam green like the one I used to own. Cargo and load capacity limited by weight and distribution. Again, either of these brackets will hold the coilover shock or the rear ShockWaves from Air Ride Technologies. There just isn't enough room. The Jim Meyer Racing Products chassis package offers up to a 10-inch step over the rearend, while the front chassis step is also available up to 4-inches more than stock! One more thing, its your truck do what you want to it.
We offer adjustable aluminum coilover shocks that are available with adjustable rebound or adjustable compression with one-knob or a two-knob adjustable model: one knob for rebound and one knob for compression or a single-knob: rebound only style or the non-adjustable coilover. Our '60-72 pickup chassis features 2X5 main center frame rails and 2X4 box tube frame rails over the front-and-rear suspensions. Some devices require an adaptor or back cover. Wilwood hubs offer only 5-on-4 ¾ or 5-on-4 ½ for their 12. Always check rear seat before exiting. All rear brake packages feature a parking brake. We also build a new custom-width round-back 9-inch housing with Dutchman alloy axles for your chassis.