If you got any original paperwork or manuals with the car, it might be in there. First with any electrical repair disconnect the battery at the negative terminal. If you choose to replace it yourself you have to remove the all covers your intake and throttle cable cover. After you reconnect the battery you need to enter your anti-theft radio code. First with any electrical repair disconnect the battery at the negative terminal. You don't have to remove the battery when changing the light on the driver's side, just pull out a couple of plastic inserts and replace them when your done.
There is a gasket that needs to be replaced between the throttle body and the intake. Resetting the codes for these systems is fairly easy after you've recharged or replaced the battery. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. Put the O ring on the new T-stat and reverse above prossess in order to properly rebuild the throttle assembly. The t-stat is at the engine block end of the lower radiator house.
Unplugging the radio antenna allows for unlimited tries and opens up a softer security mode for the radio codes. Next, using a Phillips screw driver, remove the 4 screws holding the black plastic radio frame into the dash, then pull the radio forward to remove it. How long does it take to receive my radio unlock code? Express Acura radio code 10 minutes to 1 hour code retrieval! The dealer said no problem, bring it in, and no charge. It was on a card that came with your owners manual. Type 2 Acura For all 2000 and older vehicles Radio unlock procedure Your vehicle requires that you remove the radio from the vehicle in order to retrieve your radio serial. Express Acura radio code retrieval - Retrieve radio serial Acura will have two ways of retrieving the radio serial.
If yours does not, you need to remove the radio and get the serial number from the sticker on the radio. This code is not required, unless the radio is removed from the vehicle, or the vehicles battery is disconnected. The top 5 digit number is the radio code and the lower one is the radio serial number. Its purpose is to prevent unauthorized users of your radio and will not allow your car stereo to operate without the proper code. How will I get my code? Usually within 10 minutes to 1 hour, after receiving radio information, radio serial , radio model etc.
Your anti-theft radio code was on a card that came with your owners manual. It came listed on a small white plastic card. Car companies work to prevent vehicle break-ins by including anti-theft features in high-theft items such as the stereo and navigation systems. This happens when the device is removed from the vehicle or when the battery dies or is disconnected. They couldn't get me the code unless I paid them to remove the radio, and obtain the radio serial number. Put the O ring on the new T-stat and reverse above prossess in order to properly rebuild the throttle assembly.
All codes are sent via email. Best method I could find. So look in your owners manual for that card or they may have written it down somewhere in the manual. The service manager then came out and showed me a list of items they believed I needed to do replace struts, electrical, etc. When you remove the T-stat pay attention to the position of the T-stat.
Answer it should be under warranty - there was a recall or somet … hing In order to change the front headlights you would have to remove the front bumper 2 screws and annoying clips under the hood once that is done remove the screws from the top and on the metal bar that is under the headlights. God Bless the easiest way to do this is by disconnecting the battery for about 3 minutes and connect it back. Originally the car would have come with a small card that had the number on it. Other option disconnect the antenna from the back of the radio by There is an additional trick to know if you believe you have the correct code but it isn't going through or if you have used up your 5 tries to get the correct code. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. Chesapeake, Questions and Answers Q.
One of these features is where the device deactivates itself when removed from a power source and only reactivates when a reset code is entered. Programming the Transmitter s : 1 Sit in the driver's seat and open the driver's door. You might even find that it's not as hard as you'd expected. Follow it from the radiator up to the engine block. This is how they do it at the acura dealership, they just make you wait 2 hours for your car. Reverse the steps to replace the radio.
If you are not some what mechanically inclined stop reading this right now and head to a mechanic. Disconnect the starter ignition small wire by pulling it off it's connector. Step 2: Go to and follow their instructions, they lay everything out crystal clear. I know this is a really old question but I just reset the factory stereo in my 1994 Integra and figured I could contribute some useful info. And some others here have mentioned it, it seems. Once both cables have been removed you'll have to remove the cable plate from the throttle body. I had the same problem when my battery died.
If you are putting in a replacement radio, just loosen the two small bolts holding the radio on the back of the frame, and then slide the radio out of the frame. After 10 failed attempts, the stereo locks itself for one hour, and additional attempts will fail until the hour has passed. You will also have to remove any vaccum houses that are atteched to the air intake and throttle body assymbly. To do this open the glove box, reach up inside and push out on one of clips holding the wood trim, as it comes loose grasp the trim from the front and carefully pull the trim until each clip unsnaps from the dash. After you reconnect the battery you need to enter your anti-theft radio code. That's all he will need from you to give you your radio code.