Please do not try any of following procedures if you are not familiar with computer hardware. Whether you can load the operating system or not depends on how many security settings have been enabled. I cannot login to the windows because it is corrupted. This method works well for desktop, however this is not practical for laptop user unless the warranty expired long time ago. Press the F5 or the F6 key to navigate to the Password section. I was able to unlock my Acer laptop by reading and following the instruction on you website. If you too get an error while extracting, run the.
Edit: Looks like that first answer no longer exists. CmosPwd does not display a single password that you can use to enter the Setup utility but a list. Remove the screws on the back to access the inside of the case. Press the Y key, then enter a new Supervisor Password, and re-enter it when prompted. You need to do this in order to see the code required to find the backdoor password.
When you have access to the motherboard, you need to look for a specific jumper. It will then show you another menu asking how you want it to be cracked. Express shipping is available at checkout although this is rarely quicker. I have been told by several people that I am up for another motherboard — is this true — is there no other option here … that is crazy! This is done by moving a jumper on the motherboard. Not only is it easier to open a desktop, finding the component that needs to be taken out is much easier also.
Otherwise the computer may not prompt for the password at startup. Immediately and repeatedly tap the F2 key. Turn on the computer and enter the wrong password three times. How do I get the correct password for this laptop? In Windows, click Start, then Control Panel or Start, then Settings, then Control Panel. If your item has not arrived after this time please contact us and we will send you another immediately. If you are going to reference another answer, you should cite and quote the relevant information, you feel is important. How will the latter help in the case of the former? Although the prompts for these two passwords have the same appearance, the passwords are set and removed differently.
Remove the Companion Disk and restart the computer. Unsoldering the battery incorrectly may damage your motherboard and other components, so please don't attempt this if you are inexperienced. It should be noted that many of these default passwords are for older motherboards and no longer work with newer machines. Don't worry, when you restart the computer it will go back to normal and no data will be lost. I'm not suggesting what harrymc said about removing the hard drive.
It is generally close to the backup battery on the motherboard and the jumper name associated with the word. Use the arrow keys to move to the Security tab. So use it at your own risk. Then when u have windows on there,put the hard drive in ur laptop. Never fear, all is not lost.
A good option here would be to reset, rather than flash, your firmware. If the password still remains, try another solution listed below. All you have to do here is move the switch up or down. No need to pay expensive fees to experts. The following sections contain instructions on how to do so using multiple methods. Press the F5 or the F6 key to navigate to the Password section.
To clear, remove the jumper from the two pins currently covered, and place it over the two remaining jumpers. Remove the jumper, and then turn the computer on. There will be 3 pins and the jumper will be joining the center pin to either left or right pin. In some cases, you will have to remove the jumper while the system is powered up, though to minimize risk, try doing this first with the computer off. In that case, move on to the next method. Tried all the master passwords.
This should not be performed on Laptops if you are not experienced working with laptop hardware. . The is also an excellent source of information for Windows features in general. Alternately, there may be a choice for User or Supervisor Password. Or simply click here to open video. It looks like a small watch battery.
As others have said, flashing your firmware is an option, but it may not be enough. Once you have located it, observe how the latches are holding it. An example of the various jumper positions may be seen in the image to the right. Also, you can add a password to computer bios by your own. The biggest challenge is to find this jumper. Type in a Supervisor Password at the prompt, and then type it in again, when prompted. This could mean toolbars or system modifications.